Listed below are accessories that are available for Cirris cable testers. If you have questions about which accessories go with which continuity or hipot cable tester, contact us at 1-800-441-9910.
Note: Click on the photo to see a larger image.Which Ender
 |
CP-1 | Which Ender™ capacitance detection probe identifies which end of an assembly has an open. |
| APRB-WE | Which Ender probe tip |
Power Supplies
|
RPWR-10 | Replacement power cord for the Signature 1000M, 2000, 1000R+, 1000RX, 1000HN, 1000H+, 1000HX cable testers. View the transformer's current and voltage specifications. |
| RPWR-20 | Replacement power cord for Signature CH+ hipot cable tester. View the transformer's current and voltage specifications. |
|
| RPWR-50 | Replacement power cord for the 1000LC and 500 continuity testers. View the transformer's current and voltage specifications. |
|
| RPWR-CR | Replacement power cord for easy-wire CR cable and harness tester. View the transformer's current and voltage specifications. |
|
| RPWR-11 | Replacement power cord for Signature 1100-R+ and 1100-H+ cable testers. View the transformer's current and voltage specifications. |
|
| RPWR-PT | Replacement power cord for the PT-3000 and PT-4000 Cable Pull Testers |
Printers
 |
PRNT-DM | Epson LX 300+ DOS based (Dot Matrix) printer |
 |
PRNT-BJ | Brother HL-5240 LaserJet printer |
Switches
 |
EWSH-01 | General purpose switch which can be built onto harness boards. View the switch specifications. |
PLC (Programable Logic Controller)
 |
PLC-D05 | Direct Logic 05 Programable Logic Controller (PLC) adds the ability to communicate with other test equipment and the tester. It is required on the CR and CH+ testers for digital I/O. |
Probes
|
APRB-BJ | Banana Jack Probe for Signature 5000, 1000LC, Touch1, CH+, CH2, and 1100 series cable testers. |
| APRB-PJ | Pin Jack Probe for Signature 1000M, 2000, 1000R+, 1000RX, 1000HN, 1000H+, and 1000HX cable testers. | |
| APRB-WE | Probe Tip for Which Ender | |
| AWRS-BJ | Wrist strap option for the easy-wire CR harness tester |
Frame Stands and Frame Stand Boards
 |
Allows interfacing of "non-standard" connectors to cable testers. Fits on the tester's scanner section where the cover plates normally attach. |
|
| ACIR-1+ | 1000RX / 1000HX / 1100-R+ / 1100-H+ / Touch1 cable testers |
Tilt Stands
 |
Adjustable and non-adjustable tilt stands give testers an enhanced viewing angle. | |
| ATLT-AJ | Adjustable Tilt Stand for testers: 1000HX / 1100R+ / 1100H+ / Touch1 | |
| ATLT-NA | Non-Adjustable Tilt Stand for testers: 1000HX / 1100R+ / 1100H+ / Touch1 | |
| ATLR-AJ | Adjustable Tilt Stand for testers: 1000R+ and 1000RX | |
| ATLR-NA | Non-Adjustable Tilt Stand for testers: 1000R+ and 1000RX |
Adapter Trays
 |
Fabricated from G-10 material, these trays are designed to organize and protect your Signature adapters. | |
| ARAC-SS | Single High Signature Adapters | |
| ARAC-SD | Double and Quad High Signature Adapters |
Alarm Boxes
 |
Provides a green pass light, a red fail light, and an alarm. | |
| ALRM-R+ | 1000-R+ cable tester (push-button reset) | |
| ALRM-1R | 1100-R+ cable tester (push-button reset) | |
| ALRM-H+ | 1000-H+ cable tester (push-button reset) | |
| ALRM-1H | 1100-H+ cable tester (push-button reset) |
Expansion Boxes
 |
Expands cable tester capability from 128 points up to 1024 points (128 point increments) depending on the model. | |
| C100-RA | 1100-R+ and 1000-RX cable testers | |
| C100-HA | 1100-H+ (1000V) and 1000-HX hipot testers | |
| C150-HA | 1100-H+ (1500V) hipot tester | |
| C100-TA | Touch 1 (1000V) hipot tester | |
| C150-TA | Touch 1 (1500V) hipot tester | |
| C200-TA | Touch 1 (2000V) hipot tester | |
| C10U-TA | Touch 1 Ultra hipot tester |
CH2 Ribbon Adapter Mount
 |
ADCH-34 | PCBs with mating connector for CH2 on one side and 32 Pos Dual Row Header on other side. |
| ADCH-MB | Black plastic mounting brackets to hold the connector to the CH2. |
CH2 Connector Saver Assembly
 |
ADCS-C2 | CH2 Connector Saver Assembly used to preserve the original connectors on the CH2 hipot tester. |
CH2 Rack Mount Hardware
 |
CH2 Rack Mounts | Brackets and screws to mount a CH2 hipot tester in a standard 19" rack. |
CH+ Connector Saver Assembly
 |
ADCS-CH | CH+ Connector Saver Assembly used to preserve the original connectors on the CH+ hipot tester. |
CH+ Rack Mount Hardware
 |
CH+ Rack Mounts | Brackets and screws to mount a CH+ hipot tester in a standard 19" rack. |
USB Serial Adapter
 |
USB-SER | The USB Serial Conversion Adapter allows a computer without a serial port to connect to the easy-wire CR harness tester or the Signature 1100 Series cable testers. |
Transition Boards & Cabling
   
|
ETB-ST | Screw Terminal Type Transition Board, ( 64 Positions ) |
| ETB-SLT | Screwless Terminal Type Transition Board, ( 64 Position ) | |
| ETB-USB | Adapter Transition Board, ( 64 Position ) Generally used with easy-wire software only. | |
| ETB-SHV | High Voltage Transition board. [click on photo to see board in context] | |
| ACLV-HV | 4' Ribbon Cable with (1) 64 Pos. Female Connector mounted on one end and (2) 32 pos Female IDC connectors on the other ends. "The Y Cable" |
|
| LVHV-AD | 32 Pos. LV to HV Transition Board Adapter that terminates (2) 32 pos. Y cable ends. |
Cables and Connectors
   
|
AC00-64 | 64 Position, Female, IDC Type Ribbon Connector |
| AD00-64 | 64 Position, Female, .1" Dual Row Discrete Wire Connector | |
| AC20-34 | 2' Ribbon Cable with 34 Pos. Female Connector mounted on one end only. | |
| AC20-64 | 2' Ribbon Cable with 64 Pos. Female Connector mounted on one end only. | |
| AC22-64 | 2' Ribbon Cable with 64 Pos. Female Connector mounted on both ends. | |
| AC42-64 | 4' Ribbon Cable with 64 Pos. Female Connector mounted on both ends. | |
| AC61-KF | 6' discrete 22 AWG cable with a male connector on one end only (for use with female 1000V adapter, 4-wire adapter, and CH+ analyzer). Single cable - 32 conductors in cable. | |
| AC62-KF | 6' discrete 22 AWG cables with male connector on BOTH ENDS ( A Single Cable - with 32 Conductors ) |
|
  | ||
| AD20-64 | 2'-0" long, discrete cable with 64 female connector on one end. |
|
| ACCH-CO | Mating VME style connector for CH+ without hood | |
| ACCH-CH | Mating VME style connector for CH+ with hood |
Performance Verification Check Kits
  |
Designed to verify your tester is operating to the specified standards. | PCHK-00 | Signature 1000/1000M/2000 cable testers |
| PCHK-05 | Signature 500 cable tester | |
| PCHK-11 | Signature 1100-H+ hipot tester | |
| PCHK-1H | Signature 1000H/2000H cable testers | |
| PCHK-1R | Signature 1100-R+ cable tester | |
| PCHK-50 | Signature 5000 continuity tester | |
| PCHK-5A | Signature 5000A continuity tester | |
| PCHK-CH | easy-wire CH+ hipot tester | |
| PCHK-C2 | easy-wire CH2 hipot tester | |
| PCHK-CR | easy-wire CR harness tester | |
| PCHK-HN | Signature 1000HN hipot tester | |
| PCHK-H+ | Signature 1000H+ hipot tester | |
| PCHK-LC | Signature 1000LC continuity tester | |
| PCHK-R+ | Signature 1000R+ cable tester | |
| PCHK-T1 | Signature Touch 1 hipot tester | |
| PCHK-TL | Signature Low Voltage model Touch 1 tester |
