| PHOTO OF PCB |
CIRRIS PART NUMBER |
CIRRIS BOARD NUMBER |
BOARD DESCRIPTION |
Click photo to enlarge.
|
APCB-10
|
AW 17-18430
|
The grid pattern of holes in the center section of the board is .1" center to center. The two "dual row" hole patterns on either edge of the board are .1" also and are designed to take a dual row header connector so you can ribbon cable down to a standard AHED-64 adapter installed in the tester below. (See photos above for example of how that works.)
All PCB Boards measure 3" x 6 5/8". |
Click photo to enlarge.
|
APCB-20
|
AW 17-18545
|
The grid pattern of holes on the left side of the board is .2" center to center. The two "dual row" hole patterns on the right edge of the board are .1" and are designed to take a dual row header connector so you can ribbon cable down to a standard AHED-64 adapter.
|
Click photo to enlarge.
|
APCB-2M
|
AW 17-18598
|
The grid pattern of holes in the center of the board are 2MM center to center. The four "dual row" hole patterns on both edges of the board are .1" and are designed to take a dual row header connector so you can ribbon cable down to a standard AHED-64 adapter. (Because there are no traces on the board. You must "hardwire" from the connector to the edge of the board.)
|
Click photo to enlarge.
|
APCB-05
|
AW 17-18581
|
The hole grid pattern in the center section of the board is .050" center to center. The two "dual row" hole patterns on either edge of the board are .1" and are designed to take a dual row header connector so you can ribbon cable down to a standard AHED-64 adapter installed in the tester below. (See photos above to see how that works.)
|
Click photo to enlarge.
|
APCB-50
|
AW 17-18543
|
The hole grid pattern in the center section of the board is .050" (SCSI II pattern) The "dual row" column hole patterns on the outside edges of the board are .1" and are designed to take a dual row header connector. There are traces are you can see from the center SCSI pattern to the outside dual row patterns. This allows you to easily connector up to the connector soldered on to the center of the board.
|
Click photo to enlarge.
|
APCB-SH
|
AW 17-18542
|
The hole pattern in the center of the board is: .1" center to center. The single row of holes on the left edge of the board has spacing of .156" center to center. There are no traces from the two hole patterns mentioned to the "dual row" patterns on the right edge of the board.
|
Click photo to enlarge.
|
APCB-AH
|
AW 17-18561
|
The hole pattern in the center of the board is .050" x .1" dual row.
As you can see there are traces which run to both "dual row" footprints on the outsides of the board. These "dual row" hole patterns are .1" center to center.
|
Click photo to enlarge.
|
APCB-25
|
AW 17-18548
|
Hole pattern on left is .25" grid. There are no traces to the right side "dual row" footprints. The dual row hole pattern is .1" center to center.
All PCB Boards measure 3" x 6 5/8". |
Click photo to enlarge.
|
ACLP-KY
|
Not a PCB type board.
|
Blank Kydex material routed to the same dimensions as the PCBs above. This material is strong yet easy to work with. It has a slight textured surface. (Click small photo to see larger photo which shows material texture.)
|
Click photo to enlarge.
|
ACLP-G1
|
Not a PCB type board
|
Blank G-10 material routed to the same dimensions as the PCBs above. The G-10 is stiffer material then the Kydex and it has a smooth glossy surface.
|
Click photo to enlarge. |
APCB-4S |
AW 17-18411 |
Specialty "4 Wire Kelvin" Board
Frame Stand PCB designed to allow 4 wire Kelvin testing of SCSI II style connectors up to 68 positions. |
Click photo to enlarge. |
APCB-4D |
AW 17-18441 |
Specialty "4 Wire Kelvin" Board
Frame Stand PCB designed to allow 4 wire Kelvin testing of D-Sub Pattern connectors. (15, 25, 37 positions) |
